	    ͻ
	    							
                 Compex RL2000A PnP Series Ethernet Adapter    
              Copyright (C) 1996 by PDS. All Rights Reserved.  
	    							
	    ͼ

Ŀ
 GENERAL INFORMATION 

 1) DOS and OS/2 NDIS v2.0.1 device driver
    RLPNPA.DOS v2.10 and RLPNPA.OS2 v2.10

     The NDIS drivers v2.10 for OS/2 and DOS were written to
     and tested with the Network Driver Interface Specification (NDIS)
     Version 2.0.1.

 The file layout in the MSLANMAN.DOS and MSLANMAN.OS2 directories is
 shown below:-


  MSLANMAN.DOS
     
      DRIVERS
            
             ETHERNET
                   
                    RLPNPA
                           
                            RLPNPA.DOS
                            PROTOCOL.INI
            
             NIF
                  
                   RLPNPA.NIF


  MSLANMAN.OS2
     
      DRIVERS
            
             ETHERNET
                   
                    RLPNPA
                           
                            RLPNPA.OS2
                            PROTOCOL.INI
            
             NIF
                  
                   RLPNPA.NIF

Ŀ
 INSTALLATION GUIDE  


** - IMPORTANT 
     =========
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    Recommended you run RLASET configuration utility first before 
    you proceed with install the LAN adapter driver described below. 

    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
 

 1) LAN Manager 2.0
 

     a) Start the SETUP program.

     b) Choose "Actions" from the top manual bar.

     c) Choose "Import network drivers" to load the driver.
        Insert the driver diskette into a drive and enter correct
        source drive letter. Then SETUP will create the appropriate
        directory and transfer the driver from the diskette.

	After this step, the driver is loaded.  If you want to change the
	existing driver, then you should go through the following steps:

     d) Choose "View/Modify" from the top manual bar.

     e) Press [ENTER] until you find the "Network Drivers"
        manual. In this manual, you will find the existing
        network driver configuration and all network adapters and
        protocols which it supports.

     f) Remove the existing configuration by choosing
        "Remove".

     g) Select "Compex RL2000A PnP Ethernet Adapter" in the
        "Network adapter card" box and choose the appropriate protocol
        layer in the "Protocol" box.

     h) Choose "Add Driver" to add a hardware driver and "Add
        Protocol" to add a protocol driver to the "Network
        Configuration" box.

     i) Then choose "Done" to exit to the main manual. 

     j) Before exiting the SETUP program, choose "Save" from the
        "Actions" box to update the changes you have made.

 2) LAN Manager 2.1/2.2
 

     The setup procedures for LAN Manager 2.1 is similar to LAN
     Manager 2.0.  Follow the procedure listed below to perform your
     installation.

     a) Start the SETUP program.

     b) Choose "Configuration" from the top manual bar.

     c) Choose "Network Drivers" to enter to the "Workstation
        Configuration" box.

     d) Choose "Add New Config" to check the existing network
        adapter drivers.

     e) Select "Other Driver" to import the driver from the
        diskette.

     Insert the driver diskette into a drive and enter correct 
     source drive letter. Then SETUP will create the appropriate 
     directory and transfer the driver from the diskette.


Ŀ
 INSTALLING MULTIPLE ADAPTERS 


 You may install multiple adapters (maximum four) in one
 LAN Manager system using the LAN Manager SETUP program.
 During installation, you must select the driver as many times
 as the number of adapters installed.

